Freescale Semiconductor MPC5553 Reference Manual Download | Manualshive

Page: 1083 / 1208

background image

MPC5553/MPC5554 Microcontroller Reference Manual, Rev. 5

25-44

Freescale Semiconductor

25.11.11 Ownership Trace

This section details the ownership trace features of the NZ6C3 module.

25.11.11.1 Overview

Ownership trace provides a macroscopic view, such as task flow reconstruction, when debugging software
written in a high level (or object-oriented) language. It offers the highest level of abstraction for tracking
operating system software execution. This is especially useful when the developer is not interested in
debugging at lower levels.

25.11.11.2 Ownership Trace Messaging (OTM)

Ownership trace information is messaged via the auxiliary port using an ownership trace message (OTM).
The e200z6 processor contains a Power Architecture Book E defined process ID register within the CPU.

The process ID register is updated by the operating system software to provide task/process ID
information. The contents of this register are replicated on the pins of the processor and connected to
Nexus. The process ID register value can be accessed using the

mfspr

/

mtspr

instructions. Please refer to

the

e200z6 PowerPC

TM

Core Reference Manual

for more details on the process ID register.

There are two conditions which will cause an ownership trace message.

There is one condition that will cause an ownership trace message: When new information is updated in
the OTR register or process ID register by the e200z6 processor, the data is latched within Nexus, and is
messaged out via the auxiliary port, allowing development tools to trace ownership flow.

Ownership trace information is messaged out in the following format:

Figure 25-25. Ownership Trace Message Format

25.11.11.3 OTM Error Messages

An error message occurs when a new message cannot be queued due to the message queue being full. The
FIFO will discard incoming messages until it has completely emptied the queue. After it is emptied, an
error message will be queued. The error encoding will indicate which types of messages attempted to be
queued while the FIFO was being emptied.

If only an OTM message attempts to enter the queue while it is being emptied, the error message will
incorporate the OTM only error encoding (00000). If both OTM and either BTM or DTM messages
attempt to enter the queue, the error message will incorporate the OTM and (program or data) trace error
encoding (00111). If a watchpoint also attempts to be queued while the FIFO is being emptied, then the
error message will incorporate error encoding (01000).

NOTE

The OVC bits within the DC1 register can be set to delay the CPU in order
to alleviate (but not eliminate) potential overrun situations.

PROCESS

msb

lsb

1

2

SRC

TCODE (000010)

3

6 bits

4 bits

32 bits

Fixed length = 42 bits

«
...
1081
1082
1083
1084
1085
...
»

Summary of Contents for MPC5553

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5553

Brand: RadioMaster Pages: 10

Brand: RADEMACHER Pages: 68

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: XtendLan Pages: 12

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

Brand: Samson Pages: 44

Brand: Hansen Pages: 12

Arteor 5 742 74

Brand: LEGRAND Pages: 2

Brand: Kelly Pages: 35

Brand: Badger Meter Pages: 66

Tacosol Load EXA L

Brand: Taconova Pages: 40

Brand: Blucave Pages: 2

Brand: Duke Pages: 4

Brand: VelLight Pages: 44

Brand: E-MAGA Interconnect Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands