manualshive.com logo in svg

Freescale Semiconductor MPC5553, Reference Manual

The Freescale Semiconductor MPC5553 is a powerful microcontroller designed for automotive and industrial applications. For detailed information on how to use this product, download the Reference Manual for free from 88.208.23.73:8080. This manual provides all the necessary information to optimize the performance of your MPC5553.

Share
Download
background image

MPC5553/MPC5554 Microcontroller Reference Manual, Rev. 5

1-16

Freescale Semiconductor

 

external SRAM, and asynchronous memories. In addition, the EBI supports up to four regions (via chip 
selects), along with programmed region-specific attributes.

1.5.7

SIU

The MPC5553/MPC5554 system integration unit (SIU) controls MCU reset configuration, pad 
configuration, external interrupt, general-purpose I/O (GPIO), internal peripheral multiplexing, and the 
system reset operation. The reset configuration module contains the external pin boot configuration logic. 
The pad configuration module controls the static electrical characteristics of I/O pins. The GPIO module 
provides uniform and discrete input/output control of the I/O pins of the MCU. The reset controller 
performs reset monitoring of internal and external reset sources, and drives the RSTOUT pin. The SIU is 
accessed by the e200z6 core through the crossbar switch.

1.5.8

ECSM

The error correction status module (ECSM) provides status information regarding platform memory errors 
reported by error-correcting codes. 

1.5.9

Flash

The MPC5554 provides 2 Mbytes of programmable, non-volatile, flash memory storage. The MPC5553 
provides 1.5 Mbytes of flash memory. The non-volatile memory (NVM) can be used for instruction and/or 
data storage. 

The MPC5553/MPC5554 flash also contains a flash bus interface unit (FBIU) that interfaces the system 
bus to a dedicated flash memory array controller. The FBIU supports a 64-bit data bus width at the system 
bus port, and a 256-bit read data interface to flash memory. The FBIU contains two 256-bit prefetch 
buffers, and a prefetch controller that prefetches sequential lines of data from the flash array into the buffer. 
Prefetch buffer hits allow no-wait responses. Normal flash array accesses are registered in the FBIU and 
are forwarded to the system bus on the following cycle, incurring three wait-states. Prefetch operations 
may be automatically controlled, and may be restricted to servicing a single bus master. Prefetches may 
also be restricted to being triggered for instruction or data accesses.

1.5.10

Cache

The e200z6 core supports a 32-Kbyte (MPC5554) / 8-Kbyte (MPC5553), 8-way (MPC5554) / 2-way 
(MPC5553) set-associative, unified (instruction and data) cache with a 32-byte line size. The cache 
improves system performance by providing low-latency data to the e200z6 instruction and data pipelines, 
which decouples processor performance from system memory performance. The cache is virtually indexed 
and physically tagged. The e200z6 does not provide hardware support for cache coherency in a 
multi-master environment. Software must be used to maintain cache coherency with other possible bus 
masters.

Both instruction and data accesses are performed using a single bus connected to the cache. Addresses 
from the processor to the cache are virtual addresses used to index the cache array. The memory 
management unit (MMU) provides the virtual to physical translation for use in performing the cache tag 

Summary of Contents for MPC5553

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5553

Gardena EasyPlus Operator'S Manual preview
EasyPlus
Brand: Gardena Pages: 14
Gardena 1273 Operating Instructions preview
1273
Brand: Gardena Pages: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Brand: Gantner Pages: 4
Samson 3372 User Manual preview
3372
Brand: Samson Pages: 8
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Brand: Zander Aachen Pages: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Brand: Zamel Pages: 2
National Instruments NI 9514 User Manual preview
NI 9514
Brand: National Instruments Pages: 72
ITALFARAD RC4 Operating Instructions Manual preview
RC4
Brand: ITALFARAD Pages: 32
GIESSE RACK MAX 650 Instruction And Installation Manual preview
RACK MAX 650
Brand: GIESSE Pages: 136
PI C-863 User Manual preview
C-863
Brand: PI Pages: 111
Ayra 9000-0043-8700 User Manual preview
9000-0043-8700
Brand: Ayra Pages: 19
Sunlight Supply TITAN Controls Saturn 4 Instruction Manual preview
TITAN Controls Saturn 4
Brand: Sunlight Supply Pages: 4
VistaLab 2100-0003 Operating Manual preview
2100-0003
Brand: VistaLab Pages: 20
LTH Electronics MTD75 Operation Manual preview
MTD75
Brand: LTH Electronics Pages: 266
McLelland MAP-1200PRE Owner'S Manual preview
MAP-1200PRE
Brand: McLelland Pages: 26
Sander REDOX Instructions For Use Manual preview
REDOX
Brand: Sander Pages: 8
SGM TLD-612A User Manual preview
TLD-612A
Brand: SGM Pages: 24
Landi Renzo SE 81 SIC Installation And Adjustment Manual preview
SE 81 SIC
Brand: Landi Renzo Pages: 19

Brands by name

Popular brands

Load more brands