xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
725
Chapter 71
OSPF Version 3 Command
List (RI Mode Only)
config ospfv3 router_id
<ipaddr>
enable ospfv3
disable ospfv3
config ospfv3
[ipif <ipif_name 12> | all] {area <area_id> | priority <value 0-255> | hello_interval
<sec 1-65535> | dead_interval <sec 1-65535> | instance <value 0-255> | metric <value 1-
65535> | state [enable | disable] | passive [enable | disable]}(1)
show ospfv3
{[ipif <ipif_name 12> | all]}
create ospfv3 area
<area_id> type [normal | stub {stub_summary [enable | disable] | metric
<value 0-65535>}]
config ospfv3 area
<area_id> type [normal | stub {stub_summary [enable | disable] | metric
<value 0-65535>}]
delete ospfv3 area
<area_id>
show ospfv3 area
{<area_id>}
create ospfv3 aggregation
<area_id> <ipv6networkaddr> advertise [enable | disable]
config ospfv3 aggregation
<area_id> <ipv6networkaddr> advertise [enable | disable]
delete ospfv3 aggregation
<area_id> <ipv6networkaddr>
show ospfv3 aggregation
{<area_id>}
show ospfv3 lsdb
{area <area_id> | type [rtrlink | netlink | inter_area_prefix | inter_area_router |
asextlink | link_lsa | intra_area_prefix]}
show ospfv3 neighbor
{<neighbor_id> ipif <ipif_name 12>}
show ospfv3 virtual_neighbor
{<area_id> <neighbor_id>}
create ospfv3 virtual_link
<area_id> <neighbor_id> {hello_interval <sec 1-65535> |
dead_interval <sec 1-65535> | instance <value 0-255>}
config ospfv3 virtual_link
<area_id> <neighbor_id> {hello_interval <sec 1-65535> |
dead_interval <sec 1-65535> |instance <value 0-255>}(1)
delete ospfv3 virtual_link
<area_id> <neighbor_id>
show ospfv3 virtual_link
{<area_id> <neighbor_id>}
create ipv6route redistribute dst ospfv3 src
[local | static | ripng] {mettype [1 | 2] | metric <value
1-16777214>}
config ipv6route redistribute dst ospfv3 src
[local | static | ripng] {mettype [1 | 2] | metric <value
1-16777214>}(1)
delete ipv6route redistribute dst ospfv3 src
[local | static | ripng]
71-1
config ospfv3 router_id
Description
This command is used to configure the OSPFv3 router ID.
Format
config ospfv3 router_id <ipaddr>
Parameters
<ipaddr>
- Enter a 32-bit number in the form of an IPv4 address that uniquely identifies the router
in the OSPFv3 domain. In OSPFv3, neighboring routers on a given link are always identified
by their OSPFv3 Router ID. Set 0.0.0.0 means auto-selected. Switch will select the largest
Summary of Contents for xStack DGS-3120 Series
