ARM Cortex-M3 DesignStart Technical Reference Manual Download

Page: 331 / 410

AHB Trace Macrocell Interface

ARM DDI 0337G

16-3

Unrestricted Access

Non-Confidential

16.2

CPU AHB trace macrocell interface port descriptions

Table 16-1 list the AHB interface ports.

Table 16-1 AHB interface ports

Port name

Direction

Description

HTMDHADDR[31:0]

Output

32-bit address.

HTMDHTRANS[1:0]

Output

Output indicates the type of the current data transfer. Can be IDLE,
NONSEQUENTIAL, OR SEQUENTIAL.

HTMDHSIZE[1:0]

Output

Indicates the size of the access. Can be 8, 16, or 32 bits.

HTMDHBURST[2:0]

Output

Output indicates if the transfer is part of a burst.

HTMDHPROT[3:0]

Output

Provides information on the access.

HTMDHWDATA[31:0]

Output

32-bit write data bus.

HTMDHWRITE

Output

Write not read.

HTMDHRDATA[31:0]

Output

Read data bus.

HTMDHREADY

Output

When HIGH indicates that a transfer has completed on the bus. The signal is
driven LOW to extend a transfer.

HTMDHRESP[1:0]

Output

The transfer response status. OKAY or ERROR.

HTMDHADDR[31:0]

Output

32-bit address.

HTMDHTRANS[1:0]

Output

Output indicates the type of the current data transfer. Can be IDLE,
NONSEQUENTIAL, OR SEQUENTIAL.

Summary of Contents for Cortex-M3 DesignStart













































































































































































































































































































































































































Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands

ARM Cortex-M3 DesignStart, Technical Reference Manual

Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands