ARM Cortex-M3 DesignStart Technical Reference Manual Download

Page: 382 / 410

Signal Descriptions

A-10

ARM DDI 0337G

Non-Confidential

Unrestricted Access

A.8

System bus interface

Table A-8 lists the signals of the system bus interface.

Table A-8 System bus interface

Name

Direction

Description

HADDRS[31:0]

Output

32-bit address.

HTRANSS[1:0]

Output

Indicates the type of the current transfer. Can be IDLE, NONSEQUENTIAL, OR
SEQUENTIAL.

HSIZES[2:0]

Output

Indicates the size of the access. Can be 8, 16, or 32 bits.

HBURSTS[2:0]

Output

Indicates if the transfer is part of a burst.

HPROTS[3:0]

Output

Provides information on the access.

HWDATAS[31:0]

Output

32-bit write data bus.

HWRITES

Output

Write not read.

HMASTLOCKS

Output

Indicates a transaction that must be atomic on the bus. This is only for bit-band
writes (performed as read-modify-write).

EXREQS

Output

Exclusive request.

MEMATTRS[1:0]

Output

Memory attributes. Bit 0 = Allocate, Bit 1 = shareable.

HMASTERS[1:0]

Output

Indicates the current system bus master:

•

0 = Core data side accesses or DAP access with MasterType set to 0.

•

1 = DAP accesses with MasterType set to 1.

•

2 = Core instruction side accesses. These include vector fetches that are
marked as data by

HPROTS[0]

•

3 = Reserved. This value cannot appear on

HMASTERS

HRDATAS[31:0]

Input

Read data bus.

HREADYS

Input

When HIGH indicates that a transfer has completed on the bus. The signal is driven
LOW to extend a transfer.

HRESPS[1:0]

Input

The transfer response status. OKAY or ERROR.

EXRESPS

Input

Exclusive response.

Summary of Contents for Cortex-M3 DesignStart













































































































































































































































































































































































































Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands

ARM Cortex-M3 DesignStart, Technical Reference Manual

Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands