Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 182 / 516

background image

NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560
(Active and Standby) for a ONS 15454 Multishelf Node

This procedure uses Cisco IOS to configure the Cisco Catalyst 2950 or Cisco
Catalyst 3560 for a multishelf node configuration. For more information about
the Catalyst 2950 or Catalyst 3560, refer to the Catalyst 2950 or Catalyst 3560
product documentation.

Purpose

None

Tools/Equipment

NTP-G295 Connect the ONS 15454 Multishelf Node and Subtending Shelves to
a Catalyst 2950 or Catalyst 3560, on page 146

Prerequisite Procedures

Required

Required/As Needed

Onsite or remote

Onsite/Remote

Superuser

Security Level

When Cisco Catalysts are used in a multishelf node configuration, the Cisco Catalysts can be used for other
applications as long as they do not interfere with the VLAN settings of the multishelf node configuration.

Note

• The ONS 15454 works with any VLAN ID type. The ONS 15454 M6 works with public VLAN ID of

1 and private VLAN ID of 2.

• Public and Private VLAN IDs are specified in the multishelf configuration of ONS 15454 node controller.

Procedure

Step 1

At the Cisco IOS command line interface (CLI) for the Catalyst switch, enter the following spanning tree
commands:

Example:

Switch(config)#

spanning-tree mode rapid-pvst

Switch(config)#

no spanning-tree optimize bpdu transmission

Switch(config)#

spanning-tree extend system-id

Step 2

Enter the following commands to configure Port 1:

Example:

Switch(config)#

interface FastEthernet0/1

Switch(config-if)#

switchport trunk encapsulation dot1q

Switch(config-if)#

switchport trunk allowed vlan

public VLAN ID,private VLAN ID

Switch(config-if)#

switchport mode trunk

Switch(config-if)#

switchport nonegotiate

Cisco ONS 15454 Hardware Installation Guide

152

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node

«
...
180
181
182
183
184
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Sun Storage J4200

Brand: Sun Microsystems Pages: 112

Brand: Dell Pages: 1682

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands