192
CHAPTER 10 PWC (Pulse Width Count: Pulse Width Measurement)
10.4
Operation Explanation
PWC has the measurement input pin, 8-bit input division, and so on. PWC has also the
pulse width count function. Three types of count clocks can be selected. The following
describes the basic functions/operations of the pulse width count.
●
Pulse width measurement function
Enable to measure the time/cycle between any events of input pulse by the counter.
After starting, counting will not be performed until the defined measurement start edge is inputted. Start
incremental counting after the counter which detects a start edge is cleared to "0000
H
". Stop the counting
when a stop edge is detected. The value counted in this period is stored in the register as the pulse width.
Generate an interrupt requests when the measurement ends and an overflow occurs.
Operates as follows depending on the measurement mode after the measurement end.
•In single measurement mode: Stop operation.
•In continuous measurement mode: After transferred a counter value to the buffer register, stop the
counting until the measurement start edge is inputted again.
Figure 10.4-1 Pulse Width Measurement Operation
(Single Measurement Mode / "H" Width Measurement)
Figure 10.4-2 Pulse Width Measurement Operation
(Continuous Measurement Mode / "H" Width Measurement)
Time
FFFF
H
0000
H
Co
u
nt v
a
l
u
e
S
t
a
rt
me
asu
rement
Co
u
nt
s
top
PWC inp
u
t
me
asu
red p
u
l
s
e
Co
u
nt cle
a
r
Co
u
nt
s
t
a
rt
(
S
olid line i
s
co
u
nt v
a
l
u
e)
EDIR fl
a
g
s
et (me
asu
rement end)
Time
Co
u
nt
s
top
Overflow
OVIR fl
a
g
s
et
Co
u
nt
s
t
a
rt
Co
u
nt cle
a
r
EDIR fl
a
g
s
et
(
S
olid line i
s
co
u
nt v
a
l
u
e)
FFFF
H
0000
H
Co
u
nt v
a
l
u
e
S
t
a
rt
me
asu
rement
Co
u
nt
s
top
PWC inp
u
t
me
asu
red p
u
l
s
e
Co
u
nt cle
a
r
Co
u
nt
s
t
a
rt
EDIR fl
a
g
s
et (me
asu
rement end)
Tr
a
n
s
fer d
a
t
a
to PWCR
Tr
a
n
s
fer d
a
t
a
to PWCR
Summary of Contents for FR60Lite
