manualshive.com logo in svg

Silicon Laboratories EFM32JG1, Reference Manual

The Silicon Laboratories EFM32JG1 Reference Manual is available for free download on our website. This comprehensive manual covers all aspects of using this high-performance product, providing valuable insights and instructions. Visit 88.208.23.73:8080 to easily access and download this essential manual for optimizing your experience with the EFM32JG1.

Share
Download
background image

15.3.7.2  Interactions

Whenever the I

2

C module is waiting for interaction from software, it holds the bus clock SCL low, freezing all bus activities, and the

BUSHOLD interrupt flag in I2Cn_IF is set. The action(s) required by software depends on the current state the of the I

2

C module. This

state can be read from the I2Cn_STATE register.

As an example, 

Table 15.3 I2C Master Transmitter on page 408

 shows the different states the I

2

C goes through when operating as a

Master Transmitter, i.e., a master that transmits data to a slave. As seen in the table, when a start condition has been transmitted, a
requirement is that there is an address and an R/W bit in the transmit buffer. If the transmit buffer is empty, then the BUSHOLD interrupt
flag is set, and the bus is held until data becomes available in the buffer. While waiting for the address, I2Cn_STATE has a value 0x57,
which can be used to identify exactly what the I

2

C module is waiting for.

Note:

The bus would never stop at state 0x57 if the address was available in the transmit buffer.
 

The different interactions used by the I

2

C module are listed in 

Table 15.2 I2C Interactions in Prioritized Order on page 406

 in a priori-

tized order. If the I

2

C module is in such a state that multiple courses of action are possible, then the action chosen is the one that has

the highest priority. For example, after sending out a START, if an address is present in the buffer and a STOP is also pending, then the
I

2

C will send out the STOP since it has the higher priority.

Table 15.2.  I2C Interactions in Prioritized Order

Interaction

Priority

Software action

Automatically continues if

STOP*

1

Set the STOP command bit in
I2Cn_CMD

PSTOP is set (STOP pending)
in I2Cn_STATUS

ABORT

2

Set the ABORT command bit in
I2Cn_CMD

Never, the transmission is abor-
ted

CONT*

3

Set the CONT command bit in
I2Cn_CMD

PCONT is set in I2Cn_STATUS
(CONT pending)

NACK*

4

Set the NACK command bit in
I2Cn_CMD

PNACK is set in I2Cn_STATUS
(NACK pending)

ACK*

5

Set the ACK command bit in
I2Cn_CMD

AUTOACK is set in I2Cn_CTRL
or PACK is set in I2Cn_STATUS
(ACK pending)

ADDR+W -> TXDATA

6

Write an address to the transmit
buffer with the R/W bit set

Address is available in transmit
buffer with R/W bit set

ADDR+R -> TXDATA

7

Write an address to the transmit
buffer with the R/W bit cleared

Address is available in transmit
buffer with R/W bit cleared

START*

8

Set the START command bit in
I2Cn_CMD

PSTART is set in I2Cn_STATUS
(START pending)

TXDATA/ TXDOUBLE

9

Write data to the transmit buffer Data is available in transmit buf-

fer

RXDATA/ RXDOUBLE

10

Read data from receive buffer

Space is available in receive
buffer

None

11

No interaction is required

The commands marked with a * in 

Table 15.2 I2C Interactions in Prioritized Order on page 406

 can be issued before an interaction is

required. When such a command is issued before it can be used/consumed by the I

2

C module, the command is set in a pending state,

which  can  be  read  from  the  STATUS  register.  A  pending  START  command  can  for  instance  be  identified  by  PSTART  having  a  high
value.

Whenever the I

2

C module requires an interaction, it checks the pending commands. If one or a combination of these can fulfill an inter-

action, they are consumed by the module and the transmission continues without setting the BUSHOLD interrupt flag in I2Cn_IF to get
an interaction from software. The pending status of a command goes low when it is consumed.

EFM32JG1 Reference Manual

I2C - Inter-Integrated Circuit Interface

silabs.com

 | Smart. Connected. Energy-friendly.

Preliminary Rev. 0.6  |  406

Summary of Contents for EFM32JG1


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EFM32JG1

Salda TPC User Manual preview
TPC
Brand: Salda Pages: 16
IDTECK iTDC Troubleshooting Manual preview
iTDC
Brand: IDTECK Pages: 94
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Brand: Zamel Pages: 2
Therma-Stor 4028407 Installation Instructions Manual preview
4028407
Brand: Therma-Stor Pages: 20
FuzzDog HellGazer II Quick Start Manual preview
HellGazer II
Brand: FuzzDog Pages: 9
Galil Motion Control DMC-40x0 Series Command Reference Manual preview
DMC-40x0 Series
Brand: Galil Motion Control Pages: 280
Cooper S225-50-45 Service Information preview
S225-50-45
Brand: Cooper Pages: 4
Raypak RAYTHERM 624 Specifications preview
RAYTHERM 624
Brand: Raypak Pages: 2
VeriFone Commander Site Controller Software Installation Manual preview
Commander Site Controller
Brand: VeriFone Pages: 34
Sysmac CQM1 Operation Manual preview
CQM1
Brand: Sysmac Pages: 159
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Brand: OCL Pages: 2
OBO Bettermann C50-0-255 Installation Instructions Manual preview
C50-0-255
Brand: OBO Bettermann Pages: 6
Oilon VMi 6-17 Installation And Operation Manual preview
VMi 6-17
Brand: Oilon Pages: 74
Dieffematic LINEA c400 Instructions And Recommendations For The Installer preview
LINEA c400
Brand: Dieffematic Pages: 9
Translux Fair-Play MP-50 Series Quick Reference preview
Fair-Play MP-50 Series
Brand: Translux Pages: 20
SAES NEG POWER User Manual preview
NEG POWER
Brand: SAES Pages: 36
Duke TSC-6/18M Installation Instructions preview
TSC-6/18M
Brand: Duke Pages: 4
Teracom TCW112-WD User Manual preview
TCW112-WD
Brand: Teracom Pages: 14

Brands by name

Popular brands

Load more brands