manualshive.com logo in svg

Silicon Laboratories EFM32JG1, Reference Manual

The Silicon Laboratories EFM32JG1 Reference Manual is available for free download on our website. This comprehensive manual covers all aspects of using this high-performance product, providing valuable insights and instructions. Visit 88.208.23.73:8080 to easily access and download this essential manual for optimizing your experience with the EFM32JG1.

Share
Download
background image

Bit

Name

Reset

Access Description

31:30

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in 

1.2 Conven-

tions

29:28

LPCMPBIAS

0x3

RW

LP mode comparator bias selection

LP mode comparator bias selection. Reset with POR, Hard Pin Reset, or BOD Reset.

Value

Mode

Description

0

BIAS0

Maximum load current less than 75uA.

1

BIAS1

Maximum load current less than 500uA.

2

BIAS2

Maximum load current less than 2.5mA.

3

BIAS3

Maximum load current less than 10mA.

27

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in 

1.2 Conven-

tions

26:24

LNCLIMILIMSEL

0x3

RW

Current limit level selection for current limiter in LN mode

High-side current limiter’s current limit level selection in low noise mode. The recommended setting is calculated by LNCLI-
MILIMSEL=(I_MAX+40mA)*1.5/(5mA*(1))-1, where I_MAX is the maximum average current allowed to the load,
and 40mA represents the current ripple with some margin, and the factor of 1.5 accounts for detecting error and other varia-
tions.  For  strong  battery,  it  is  recommended  to  have  I_MAX=200mA.  It  should  never  have  I_MAX  higher  than  200mA  to
avoid reliability issues. Reset with POR, Hard Pin Reset, or BOD reset.

23

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in 

1.2 Conven-

tions

22:20

LPCLIMILIMSEL

0x3

RW

Current limit level selection for current limiter in LP mode

High-side  current  limiter’s  current  limit  level  selection  in  low  power  mode.  It  is  calculated  by  LPCLIMILIMSEL=(I_MAX
+40mA)*1.5/(5mA*(1))-1. To optimize the power efficiency, it is recommended to have PFETCNT=7 and (IMAX
+40mA)*1.5=80mA, and consequently calculated LPCLIMILIMSEL=1. Reset with POR, Hard Pin Reset, or BOD reset.

19:16

BYPLIMSEL

0x0

RW

Current Limit In Bypass Mode

Set current limit in bypass mode when BYPLIMEN equals one. The limit is from 20mA to 320mA, with 20mA/step. Reset
with POR, Hard Pin Reset, or BOD Reset.

15:12

NFETCNT

0x7

RW

NFET switch number selection

NFET power switch count number. The selected number of switches are 1. This value applies to both LN and
LP mode. Because of this, when transitioning from LN to LP mode, software may need to update the NFETCNT setting
desired for LP mode while still in LN mode. This may cause a very momentary efficiency hit. Reset with POR, Hard Pin
Reset, or BOD Reset.

11:8

PFETCNT

0x7

RW

PFET switch number selection

PFET power switch count number. The selected number of switches are 1. This value applies to both LN and
LP mode. Because of this, when transitioning from LN to LP mode, software may need to update the PFETCNT setting
desired for LP mode while still in LN mode. This may cause a very momentary efficiency hit. Reset with POR, Hard Pin
Reset, or BOD Reset.

7:1

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in 

1.2 Conven-

tions

0

LNFORCECCM

0

RW

Force DCDC into CCM mode in low noise operation

When this bit is set to 1 in low noise mode, the zero detector is configured as zero-crossing detector and the DCDC will be
in forced CCM mode. The threshold set by ZDETILIMSEL will be ignored. When this bit is set to 0 in low noise mode, the
zero detector is configured as reverse-current limiter and the DCDC will be in DCM mode. The reverse current limit level is
set by ZDETILIMSEL. In low power mode, the zero detector is always configured as zero-crossing detector. Reset with
POR, Hard Pin Reset, or BOD reset.

EFM32JG1 Reference Manual

EMU - Energy Management Unit

silabs.com

 | Smart. Connected. Energy-friendly.

Preliminary Rev. 0.6  |  193

Summary of Contents for EFM32JG1


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EFM32JG1

Particle B Series Quick Start Manual preview
B Series
Brand: Particle Pages: 6
NAiS FP2 Technical Manual preview
FP2
Brand: NAiS Pages: 144
Matelec FPC-36040 Owner'S Operation Manual preview
FPC-36040
Brand: Matelec Pages: 16
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Brand: WAC Pages: 5
KIPI ecoMAX360P1-C Installation And Operating Manual preview
ecoMAX360P1-C
Brand: KIPI Pages: 44
NOCO Genius CURTIS DC Series Installation Instruction preview
CURTIS DC Series
Brand: NOCO Genius Pages: 2
Xylem Aquavar AB2 Quick Start Manual preview
Aquavar AB2
Brand: Xylem Pages: 2
Trane Technologies BAYSTAT033AC Installation Manual preview
BAYSTAT033AC
Brand: Trane Technologies Pages: 8
Atmel AT91 ARM Thumb Application Note preview
AT91 ARM Thumb
Brand: Atmel Pages: 12
Patton SmartNode 5501 User Manual preview
SmartNode 5501
Brand: Patton Pages: 56
Acard PCI-to-IDE ATA-133 User Manual preview
PCI-to-IDE ATA-133
Brand: Acard Pages: 33
National Instruments cRIO-9037 Getting Started Manual preview
cRIO-9037
Brand: National Instruments Pages: 20
Active-semi ACT4910EVK1-121 User Manual preview
ACT4910EVK1-121
Brand: Active-semi Pages: 15
Danfoss EKC 531D1 Instructions Manual preview
EKC 531D1
Brand: Danfoss Pages: 18
Zapi SEM-Zero Manual preview
SEM-Zero
Brand: Zapi Pages: 39
Dataprobe iBootBar iBP-N15 Installation And Operations preview
iBootBar iBP-N15
Brand: Dataprobe Pages: 21
Mophie 1190_RCN-RMT-BLk User Manual preview
1190_RCN-RMT-BLk
Brand: Mophie Pages: 10
Avery Weigh-Tronix GSE 460 User Instructions preview
GSE 460
Brand: Avery Weigh-Tronix Pages: 48

Brands by name

Popular brands

Load more brands