Cisco ASR 9000 Series Command Reference Manual Download

Page: 126 / 1138

For the

interface-path-id

argument, use the following guidelines:

•

If specifying a physical interface, the naming notation is

rack

slot

module

port

. The slash between values

is required as part of the notation. An explanation of each component of the naming notation is as follows:

◦

rack

: Chassis number of the rack.

◦

slot

: Physical slot number of the line card.

◦

module

: Module number. A physical layer interface module (PLIM) is always 0.

◦

port

: Physical port number of the interface.

•

If specifying a virtual interface, the number range varies, depending on interface type.

Task ID

Operations

Task ID

read

Required in addition to the interface (read) task ID to
use the

control

keyword only.

Note

cisco-support

read

dwdm

read

interface

read

sonet-sdh

Examples

The following example shows sample output from the

show controllers hundredGigE phy

command for

A9K-2x100GE line card:

RP/0/RSP0/CPU0:router#

show controller hundredGigE 0/9/0/0 phy

PHY data for interface: HundredGigE0/9/0/0:

64B66B

Lane

Sync

PCS

Virt

PCS

Service

Block

Marker

Header

Lane

Lock

Sync

Err Cnt

BIP Errors

Error Mapping

---------

----------

----- -------

Locked

Clean 0

Locked

Clean 10

Locked

Clean 1

Locked

Clean 11

Locked

Clean 12

Locked

Clean 2

Locked

Clean 3

Locked

Clean 13

Locked

Clean 14

Locked

Clean 4

Locked

Clean 15

Locked

Clean 5

Locked

Clean 6

Locked

Clean 16

Locked

Clean 17

Locked

Clean 7

Locked

Clean 8

Locked

Clean 18

Locked

Clean 9

Locked

Clean 19

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

106

Ethernet Interface Commands on the Cisco ASR 9000 Series Router

show controllers (Ethernet)

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands