Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 622 / 1138

background image

lacp period short

To enable a short period time interval for the transmission and reception of Link Aggregation Control Protocol
(LACP) packets, use the

lacp period short

command in interface configuration mode. To return to the default

short period, use the

no

form of this command.

lacp period short

[

receive interval

] [

transmit interval

]

no lacp period short

[

receive interval

] [

transmit interval

]

Syntax Description

Time interval (in milliseconds) for receiving LACP packets when LACP short
period is enabled. The range is 100 to 1000 and must be multiples of 100, such as
100, 200, 300, and so on.

receive interval

Time interval (in milliseconds) for transmitting LACP packets when LACP short
period is enabled. The range is 100 to 1000 and must be multiples of 100, such as
100, 200, 300, and so on.

transmit interval

Command Default

The default is 1000.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

When you configure a custom LACP short period

transmit

interval at one end of a link, you must configure

the same time period for the

receive

interval at the other end of the link.

You must always configure the

transmit

interval at both ends of the connection before you configure the

receive

interval at either end of the connection. Failure to configure the

transmit

interval at both ends first

results in route flapping (a route going up and down continuously). When you remove a custom LACP
short period, you must do it in reverse order. You must remove the

receive

intervals first and then the

transmit

intervals.

Note

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

602

Link Bundling Commands on the Cisco ASR 9000 Series Router

lacp period short

«
...
620
621
622
623
624
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: rainforest Pages: 20

Brand: Luminext Pages: 8

Brand: Bivocom Pages: 49

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

Brand: Wintec Pages: 14

Brand: Pace Pages: 2

Brand: Naviecare Pages: 9

Brand: Dusun Pages: 8

Brand: Moeller Pages: 78

Brand: RTA Pages: 81

Brand: LANSITEC Pages: 25

MultiVOIP MVP130BG

Brand: Bogen Pages: 2

Brand: ICC Pages: 54

Brand: CALEFFI Pages: 20

Brand: Peak Pages: 73

Brand: Allo.com Pages: 62

Brand: Hitron Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands