Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 313 / 1138

background image

•

Received packet rate

–

displayed in packets per second when at least two responses are received. This

approximate rate of response is the time between the first response received and the last response received,
divided by the total number of responses received.

Task ID

Operations

Task ID

execute

basic-services

execute

ethernet-services

Examples

The following example shows how to send an Ethernet CFM loopback message:

RP/0/RSP0/CPU0:router#

ping ethernet cfm domain D1 service S1 mep-id 16 source

interface GigabitEthernet 0/0/0/0

Type escape sequence to abort.
Sending 5 CFM Loopbacks, timeout is 2 seconds -
Domain foo (level 2), Service foo
Source: MEP ID 1, interface GigabitEthernet0/0/0/0
Target: 0001.0002.0003 (MEP ID 16):

Running (5s) ...

Success rate is 60.0 percent (3/5), round-trip min/avg/max = 1251/1349/1402 ms
Out-of-sequence: 0.0 percent (0/3)
Bad data: 0.0 percent (0/3)
Received packet rate: 1.4 pps

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

293

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

ping ethernet cfm

«
...
311
312
313
314
315
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Yes Pages: 2

Brand: SVS Pages: 4

Brand: NetComm Pages: 2

Brand: Comtrend Corporation Pages: 84

Brand: Hirschmann Pages: 44

Brand: Asus Pages: 39

HomePortal 1000

Brand: 2Wire Pages: 44

Brand: 2Wire Pages: 86

Brand: Vaisala Pages: 32

Brand: Vaillant Pages: 40

EZ Connect SMC8014WG-SI

Brand: SMC Networks Pages: 2

EX500-GPN2 Series

Brand: SMC Networks Pages: 2

DOCSIS 3.0 Commercial Cable Modem Gateway SMCD3G-BIZ

Brand: SMC Networks Pages: 2

EZ Networking SMC8013WG

Brand: SMC Networks Pages: 42

LEC-GPR1 Series

Brand: SMC Networks Pages: 59

Brand: SolarEdge Pages: 49

Brand: Guest Internet Pages: 2

Brand: Zhone Pages: 226

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands