Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1108 / 1374

background image

MSC8144E Reference Manual, Rev. 3

25-6

Freescale

Semiconductor

Debugging, Profiling, and Performance Monitoring

Table 25-3 describes the 8-bit instructions coded in the Instruction Register.

clock_end_

count

3

Clock End Count
Indicates that the counter in the clock block completed
its count.

0

Clock block done signal not asserted

1

Clock block done signal asserted

retention-

stopped

2

Retention Stopped
Indicates whether all of the activated MBISTs in
retention mode have stopped. This bit is cleared by
assertion of HRESET or MBIST initiation.

0

An activated MBIST in retention mode has
not stopped, or no MBIST retention stop
was performed since the last HRESET
assertion

1

All activated MBISTs in retention mode
stopped.

—

1–0

Contains value (01) required by the JTAG standard

Read-only

Figure 25-3. Instruction Register (IR) Configuration

Table 25-3. Instruction Decoding

Opcode

Instruction

Updates IR

Description

Standard Instructions

0x00

EXTEST

Yes

Selects the Boundary Scan Register (BSR). EXTEST also asserts internal
reset for the MSC8144E system logic to force a predictable internal state
while external boundary scan operations are performed. By using the TAP,
the register can:
• Scan user-defined values into the output buffers
• Capture values presented to inputs
• Control the direction of bidirectional signals
• Control the output drive of tri-statable outputs
For details on the function and use of EXTEST, refer to the IEEE Std.
1149.1 documentation. Although the latest specification recommends not
using all zeroes, it was mandated by earlier versions of the specification and
is retained for backward compatibility.

0xF0

SAMPLE

Yes

SAMPLE provides a means to obtain a snapshot of system data and control
signals.

0xF0

PRELOAD

Yes

Initializes the BSR output cells prior to the selection of EXTEST. This
initialization ensures that known data appears on the outputs when an
EXTEST instruction is entered.

Table 25-2. Instruction Register Capture and SC3400 Core Status Values

Name/bits

Description

Settings

Parallel

From TDI

Clock-IR

C

D

1

1

MUX

G1

C

D

Parallel
Input

Update-IR

Shift-IR

Output

To next cell or TDO

«
...
1106
1107
1108
1109
1110
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

Brand: Phytec Pages: 53

Brand: ZyXEL Communications Pages: 2

Brand: Dahua Pages: 24

Brand: Qlogic Pages: 2

Procont LMC-008-IO

Brand: janitza Pages: 28

Brand: Renesas Pages: 20

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

Brand: H3C Pages: 9

2000 IDU Series

Brand: EMS Pages: 52

Brand: ACTi Pages: 12

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: Supermicro Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands