manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at 88.208.23.73:8080.

Share
Download
background image

RapidIO Message Unit

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

16-77

Internal error for an earlier posted frame 
queue entry memory write and a 
subsequent frame queue entry memory 
write is posted before the internal error is 
detected.
An internal error may or may not occur 
during the subsequent frame queue entry 
memory write. The frame queue could be 
for the same message or a different 
message

Error checking level: 4
Interrupt generated: No
Status bit set: None
Queue entry written in local memory: Yes
Response status: Error
Logical/Transport Layer Capture Register:
Comments:

Message request to request time-out for 
multi-segment messages

Error checking level: Unrelated
Interrupt generated: Serial RapidIO error/write-port if LTLEECSR[MRT] set. 
Serial RapidIO error/write-port if OMxMR[EIE] is set.
Status bit set: Message request time-out in the Logical/Transport Layer Error 
Detect CSR LTLEDCSR[MRT]. IMxSR[MRT] bit is set.
Queue entry written in local memory: No
Response status: No
Logical/Transport Layer Capture Register: Updated with the previous 
message request packet except that the message segment field (bits 4–7 of 
LTLCCCSR[MI]) is updated with the lowest message segment number not yet 
received.

2

Comments: All message segments received before the time-out update 
memory. The enqueue pointer is not incremented. The message operation 
completes.

Notes: 1.

These error types are actually detected in the RapidIO port, not in the message controller.

2.

In small transport size configuration using the packet, the following allocations are made:

• LTLACCSR[XA] gets the extended address (packet bits 78–79).
• LTLACCSR[A] gets the address (packet bits 48–76).
• LTLDIDCCSR[MDID] gets 0.
• LTLDIDCCSR[DID] gets the least significant byte of the destination ID (packet bits 16–23).
• LTLDIDCCSR[MSID] gets 0.
• LTLDIDCCSR[SID] gets the least significant byte of the source ID (packet bits 24–31).
• LTLCCCSR[FT] gets the ftype (packet bits 12–15).
• LTLCCCSR[TT] gets the ttype (packet bits 32–35).
• LTLCCCSR[MI] gets the msg info (packet bits 40–47). 

In large transport size configuration using the packet, the following allocations are made:

• LTLACCSR[XA] gets the extended address (packet bits 94–95)
• LTLACCSR[A] gets the address (packet bits 64–92)
• LTLDIDCCSR[MDID] gets the most significant byte of the destination ID (packet bits 16–23)
• LTLDIDCCSR[DID] gets the least significant byte of the destination ID (packet bits 24–31)
• LTLDIDCCSR[MSID] gets the most significant byte of the source ID (packet bits 32–39)
• LTLDIDCCSR[SID] gets the least significant byte of the source ID (packet bits 40–47)
• LTLCCCSR[FT] gets the ftype (packet bits 12–15)
• LTLCCCSR[TT] gets the ttype (packet bits 48–51)
• LTLCCCSR[MI] gets the msg info (packet bits 56–63).

Table 16-31.  Inbound Message Hardware Errors

Error

Description

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Brand: D-Link Pages: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Brand: D-Link Pages: 78
2N OfficeRoute Quick Manual preview
OfficeRoute
Brand: 2N Pages: 11
2N stargate How To Set preview
stargate
Brand: 2N Pages: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Brand: 2N Telekomunikace Pages: 24
Ratoc Systems SmartMedia Adapter PC Card REX-SMA01F Product Manual preview
SmartMedia Adapter PC Card REX-SMA01F
Brand: Ratoc Systems Pages: 75
Zhone 6211 Quick Installation Instructions preview
6211
Brand: Zhone Pages: 1
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Brand: Opengear Pages: 2
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
ZALMAN CNPS12X User Manual preview
CNPS12X
Brand: ZALMAN Pages: 11
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Brand: ACTi Pages: 12
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
Logicube ZCLONE User Manual preview
ZCLONE
Brand: Logicube Pages: 56
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4

Brands by name

Popular brands

Load more brands