manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at 88.208.23.73:8080.

Share
Download
background image

Functional Description

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

15-15

When the VCOP asserts PCI_SERR, it sets the signaled-system-error bit in the configuration 
space status register. Additionally, if the error is an address parity error, the parity-error-detected 
bit is set; reporting an address parity error on PCI_SERR is conditioned on the 
parity-error-response bit being enabled in the command register. PCI_SERR is asserted when the 
VCOP detects an address parity error while acting as a target. Figure 15-6 shows where the 
VCOP could detect an address parity error and assert PCI_SERR or where the VCOP, acting as 
an initiator, checks for the assertion of PCI_SERR signaled by the target detecting an address 
parity error.

As a target that asserts PCI_SERR on an address parity, the VCOP completes the transaction on 
the PCI bus, aborting internally if the transaction is a write to system memory. If PCI_PERR is 
asserted during a VCOP write to PCI, the VCOP attempts to continue the transfer, allowing the 
target to abort/disconnect if desired. If the VCOP detects a parity error on a read from PCI, the 
VCOP aborts the transaction internally and continues the transfer on the PCI bus, allowing the 
target to abort/disconnect if desired.

In all cases of parity errors on the PCI bus, regardless of the parity-error-response bit, information 
about the transaction is logged in the PCI error control capture register, the PCI error address 
capture register and the PCI error data capture register; an interrupt is also asserted to the core as 
an option.

15.1.8.5   PCI Inbound Address Translation

For inbound transactions (transactions generated by an external initiator on the PCI bus where the 
VCOP responds as a target device), the VCOP only responds to PCI addresses within the 
windows mapped by the PCI inbound base address registers (PIBARs) or PIMMR base address 
register (PIMMBACR). If there is an address hit in PIMMRBACR, the PCI address is translated 
from PCI space to a 32 Mbyte address space starting at address 0xFE000000 in the local memory 
space. This allows an external initiator to access local memory mapped registers. If there is an 
address hit in one of the PIBARs, the PCI address is translated from PCI space to local memory 
space through the associated PCI inbound translation address registers (PITARs). This allows an 
external initiator to access local memory. Each PIBAR register is associated with a PITAR and 
PIWAR which are located in the VCOP PCI CSR space. Figure 15-7 shows an example 
translation window for inbound memory accesses.

There are three full sets of inbound translation registers, in addition to the PIMMR base address 
register, allowing four simultaneous translation windows, one to a fixed destination and three 
programmable. Only two of the programmable windows can be mapped anywhere in the 64-bit 
PCI address space. Window 0 and the PIMMR window can only be mapped within the lowest 
4-Gbyte space. Software can move the programmable translation base addresses during run-time 
to access different portions of local memory, but the PCI inbound translation windows may not 
overlap or be translated to the PCI Outbound Window (0xE0000000 to 0xE7FFFFFF in the local 
memory space).

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Freescale Semiconductor FRDM-STBC-SA9500 Quick Reference Card preview
FRDM-STBC-SA9500
Brand: Freescale Semiconductor Pages: 2
Zoom B9.1ut Operation Manual preview
B9.1ut
Brand: Zoom Pages: 88
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
Marani LPP-440A User Manual preview
LPP-440A
Brand: Marani Pages: 39
Intel 500 - DATASHEET REV 003 Datasheet preview
500 - DATASHEET REV 003
Brand: Intel Pages: 67
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
LevelOne GSW-0890 Quick Installation Manual preview
GSW-0890
Brand: LevelOne Pages: 4
ekwb 3831109810316 User Manual preview
3831109810316
Brand: ekwb Pages: 16
ICP GDT6618RD Addendum preview
GDT6618RD
Brand: ICP Pages: 111
NCD Gen3 Ethernet Module Quick Start Manual preview
Gen3 Ethernet Module
Brand: NCD Pages: 18
ZALMAN CNPS20LQ User Manual preview
CNPS20LQ
Brand: ZALMAN Pages: 12
Martin 90523000 User Manual preview
90523000
Brand: Martin Pages: 41
IBA ibaPADU-S-IT-16 Manual preview
ibaPADU-S-IT-16
Brand: IBA Pages: 80
Imagine communications Selenio SNP-GW-3GX32 User Manual preview
Selenio SNP-GW-3GX32
Brand: Imagine communications Pages: 153
TQ STKa64xxL Quick Start Manual preview
STKa64xxL
Brand: TQ Pages: 2
Aprotech INTEL CORE i5 SYSTEM BOARD User Manual preview
INTEL CORE i5 SYSTEM BOARD
Brand: Aprotech Pages: 154

Brands by name

Popular brands

Load more brands