manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at 88.208.23.73:8080.

Share
Download
background image

Port-Write Controller

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

16-99

Table 16-42 lists the port-write programming errors. 

Port-write controller 
enabled but in the error 
state and port-write 
received

Error checking level: 2
Interrupt generated: No
Status bit set: None
Queue Entry Written in local memory: No
Response status: No response
Logical/Transport Layer Capture Register: 
Comments: Packet is ignored and discarded.

Internal error during the 
write of the port-write 
queue entry to memory

Error checking level: 3
Interrupt generated: Serial RapidIO error/write-port if IPWMR[EIE] is set.
Status bit set: Transaction error in the Port-write status register (IPWSR[TE]). Port-write Failed 
in the Port-write and Doorbell CSR (PWDCSR[PFA]).
Queue Entry Written in local memory: No
Response status: No response
Logical/Transport Layer Capture Register: 
Comments: Port-write controller stops after the current port-write operation completes.

Notes: 1.

These error types are actually detected in the RapidIO port, not in the port-write controller.

2.

In small transport size configuration using the packet, the following allocations are made:

• LTLACCSR[XA] gets the extended address (packet bits 78–79).
• LTLACCSR[A] gets the address (packet bits 48–76).
• LTLDIDCCSR[MDID] gets 0.
• LTLDIDCCSR[DID] gets the least significant byte of the destination ID (packet bits 16–23).
• LTLDIDCCSR[MSID] gets 0.
• LTLDIDCCSR[SID] gets the least significant byte of the source ID (packet bits 24–31).
• LTLCCCSR[FT] gets the ftype (packet bits 12–15).
• LTLCCCSR[TT] gets the ttype (packet bits 32–35).
• LTLCCCSR[MI] gets 0.

In large transport size configuration using the packet, the following allocations are made:

• LTLACCSR[XA] gets the extended address (packet bits 94–95).
• LTLACCSR[A] gets the address (packet bits 64– 92).
• LTLDIDCCSR[MDID] gets the most significant byte of the destination ID (packet bits 16–23).
• LTLDIDCCSR[DID] gets the least significant byte of the destination ID (packet bits 24–31).
• LTLDIDCCSR[MSID] gets the most significant byte of the source ID (packet bits 32–39).
• LTLDIDCCSR[SID] gets the least significant byte of the source ID (packet bits 40–47).
• LTLCCCSR[FT] gets the ftype (packet bits 12–15).
• LTLCCCSR[TT] gets the ttype (packet bits 48 –51).
• LTLCCCSR[MI] gets 0.

Table 16-42.  Inbound Port-Write Programming Errors

Error

Interrupt 

Generated

Status Bit Set

Comments

Port-write queue entry written to 
non-existent memory

No

No

When a write to memory occurs, the memory 
controller causes its own interrupt and update its 
own capture registers. An internal error response is 
returned. When the port-write controller receives the 
error response it sets the transaction error bit 
(IPWSR[TE]) and enters the error state.

Table 16-41.  Inbound Port-Write Hardware Errors

Error

Description

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Brand: TDK Pages: 2
Paradyne MIM-4000F Installation Instructions Manual preview
MIM-4000F
Brand: Paradyne Pages: 6
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
Crest Audio NC-MCO - TECHNICAL Technical Data preview
NC-MCO - TECHNICAL
Brand: Crest Audio Pages: 2
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Brand: ADTRAN Pages: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Brand: Aim Pages: 35
Commell MP-6802 User Manual preview
MP-6802
Brand: Commell Pages: 18
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Brand: Ceragon Pages: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Brand: Enterasys Pages: 2
Brickcom NR-2008 User Manual preview
NR-2008
Brand: Brickcom Pages: 184
OWC ACCELSIOR 8M2 Assembly Manual & User Manual preview
ACCELSIOR 8M2
Brand: OWC Pages: 9
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Adeunis RF COMFORT LwM2M User Manual preview
COMFORT LwM2M
Brand: Adeunis RF Pages: 68
Fujitsu 467 Manual preview
467
Brand: Fujitsu Pages: 36
Huawei CR-P1RS Specifications preview
CR-P1RS
Brand: Huawei Pages: 2
Huawei FusionModule 500 Quick Manual preview
FusionModule 500
Brand: Huawei Pages: 29
Huawei CR-A2HFF Specifications preview
CR-A2HFF
Brand: Huawei Pages: 3

Brands by name

Popular brands

Load more brands