Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1335 / 1374

background image

Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

26-147

26.5.9.9 MDEU End_of_Message Register (MDEUEOMR)

The End_of_message Register in the MDEU is used to indicate an authentication operation may
be completed. After the final message block is written to the input FIFO, the End_of_Message
Register must be written. The value in the Data Size Register is used to determine how many bits
of the final message block (always 512) are processed. Note that this register has no data size,
and during the write operation, the core processor data bus is not read. Hence, any data value is
accepted. Normally, a write operation with a zero data value is performed. Reading from this
register is not meaningful, but a zero value is always returned, and no error is generated. Writing
to this register is merely a trigger causing the MDEU to process the final block of a message,
allowing it to signal done interrupt.

26.5.9.10 MDEU Context Registers (MDEUCR)

For MDEU, context consists of the hash plus the message length count. Write access to this
register block allows continuation of a previous hash. Reading these registers provides the
resulting message digest or HMAC along with an aggregate bit count.

Note:

SHA-1and SHA-256 are big endian. MD5 is little endian. The MDEU module
internally reverses the endianness of the five registers A, B, C, D, and E upon writing
to or reading from the MDEU context if the MDEU Mode Register indicates MD5 is
the hash of choice. Most other endian considerations are performed as 8-byte swaps. In
this case, 4-byte endianness swapping is performed within the A, B, C, D, and E fields
as individual registers. Reading this memory location while the module is not done
generates an error interrupt.

MDEUEOMR

MDEU End_of_ Message Register

Offset 0xC6050

Bits

63

62

61

60

59

58

57

56

55

54

53

52

51

50

49

48

Field

—

Type

W

Reset 0x0000

Bits

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

Field

—

Type

W

Reset 0x0000

Bits 31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Field

—

Type

W

Reset 0x0000

Bits

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Field

—

Type

W

Reset 0x0000

«
...
1333
1334
1335
1336
1337
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: D-Link Pages: 15

Brand: National Instruments Pages: 11

Brand: Dahua Pages: 24

Brand: Avolites Pages: 24

Proventia A1204

Brand: Internet Security Systems Pages: 42

Through Hole Power Inductors 1411

Brand: Delta Electronics Pages: 1

Brand: EMTRUST Pages: 103

Brand: Network Critical Pages: 200

Brand: Loopcomm Pages: 2

Brand: ivideon Pages: 11

Brand: Intel Pages: 578

Secure Site Manager 16

Brand: Black Box Pages: 16

Brand: Allen-Bradley Pages: 76

Brand: H3C Pages: 62

Brand: Forcepoint Pages: 2

EXTREME PROCESSOR UNIT

Brand: Jefftron Pages: 6

Brand: JETWAY Pages: 54

Brand: Extron electronics Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands