Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1110 / 1374

background image

MSC8144E Reference Manual, Rev. 3

25-8

Freescale

Semiconductor

Debugging, Profiling, and Performance Monitoring

TLM

0x03

TLM_SELECT

Yes

Private instruction that provides access to the TAP Linking Module.

0x04

TLM_HOLD

No

Private instruction that provides access to a TAP Linking Module. The most
recent instruction that updated the Instruction Register is not overwritten by
this instruction. Both the TLM Update Register and whatever else is
selected by the instruction in the IR receive the TDI, but only the TLM Shift
Register sends data to TDO.

OCE Instructions

0xA0

ENABLE_ONCE

Yes

Not included in the IEEE Std. 1149.1. This public instruction allows you to
perform system debug functions. When the ENABLE_ONCE instruction is
decoded, TDI and TDO connect directly to the OCE registers. The OCE
controller selects the specific OCE register connected between TDI and
TDO, depending on the OCE instruction being executed. All communication
with the OCE controller is through the

SELECT

-

DR

-

SCAN

path of the JTAG

TAP Controller. Before the ENABLE_ONCE instruction is selected, the
CHOOSE_ONCE instruction should be executed to define which OCE is to
be activated.
Note:

This instruction is valid only if the core processor is running.

0xA1

DEBUG_REQUEST

Yes

Not included in the IEEE Std. 1149.1. This public instruction allows you to
generate a debug request signal to the MSC8144E. When the
DEBUG_REQUEST instruction is decoded, TDI and TDO connect to the
OCE registers. In addition, ENABLE_ONCE is active and forced to request
Debug mode from the MSC8144E to perform system debug functions.
Before the DEBUG_REQUEST instruction is selected, the
CHOOSE_ONCE instruction should be executed to define which OCE
module is to be selected for DEBUG_REQUEST.
Note:

Issuing this instruction does not ensure that the SC3400 core
enters the debug state. Monitor the core status to make sure that it
has stopped.

0xA2

CHOOSE_ONCE

Yes

Not included in the IEEE Std. 1149.1. This instruction enables selected
SC3400 OCE modules. All instructions executed after this one target only
the selected OCE set. Therefore, this instruction always executes,
regardless of the selected OCE set.

0xA3

RD_STATUS

Yes

The status of the OCE can be read from a dedicated status register inside
the OCE by the JTAG instruction, RD_STATUS.

Table 25-3. Instruction Decoding (Continued)

Opcode

Instruction

Updates IR

Description

«
...
1108
1109
1110
1111
1112
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Ubiquiti Pages: 24

Brand: Ubiquiti Pages: 23

Brand: Delta Pages: 2

Power Control Processor

Brand: ETC Pages: 64

Core 2 Quad Q9400

Brand: Intel Pages: 2

Brand: Magma Pages: 2

Brand: Cypress Semiconductor Pages: 15

Brand: Xantech Pages: 16

Brand: Cypress Semiconductor Pages: 38

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

Brand: SilverStone Pages: 16

Lexicon MPX 200

Brand: Harman Pages: 77

Brand: Nexus Pages: 9

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

Brand: NEC Pages: 170

Threat Analysis Reporter TAR HL/SL/MSA

Brand: 8e6 Technologies Pages: 22

Audio Plus 3200

Brand: Zoltrix Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands