manualshive.com logo in svg

Freescale Semiconductor PXR4030, Reference Manual

The Freescale Semiconductor PXR4030 Reference Manual is available for free download on 88.208.23.73:8080. This comprehensive manual provides detailed instructions on utilizing the product's features and functionalities. Get your copy of the manual now to maximize the performance of your PXR4030 device.

Share
Download
background image

Nexus Development Interface (NDI)

31-4

Freescale Semiconductor

PXR40 Microcontroller Reference Manual, Rev. 1

— FlexRay Nexus trace via data write messaging (DWM) and data read messaging (DRM). This 

allows the development tool to trace FlexRay generated reads and/or writes to selected address 
ranges in the device’s memory map.

— Watchpoint messaging (WPM) via the auxiliary port.

— Watchpoint trigger enable/disable of data trace messaging.

•

eTPU development support features (NDEDI)

— IEEE-ISTO 5001-2002 standard Class 3 compliant for the eTPU engines.

— Data trace via data write messaging and data read messaging. This allows the development tool 

to trace reads and writes to selected shared parameter RAM (SPRAM) address ranges. Four 
data trace windows are shared by the two eTPU engines.

— Ownership trace via ownership trace messaging (OTM). OTM facilitates ownership trace by 

providing visibility of which channel is being serviced. An ownership trace message is 
transmitted to indicate when a new channel service request is scheduled, allowing the 
development tools to trace task flow. A special OTM is sent when the engine enters in idle state, 
meaning that all requests were serviced and no new requests are yet scheduled.

— Program trace via branch trace messaging. BTM displays program flow discontinuities (start, 

jumps, return, etc.), allowing the development tool to interpolate what transpires between the 
discontinuities. Thus static code can be traced. The branch trace messaging method uses the 
branch/predicate method to reduce the number of generated messages.

— Watchpoint messaging via the auxiliary port. WPM provides visibility of the occurrence of the 

eTPU’s’ watchpoints and breakpoints.

— Nexus based breakpoint/watchpoint configuration and single step support.

•

Run-time access to the on-chip memory map via the Nexus read/write access protocol. This feature 
supports accesses for run-time internal visibility, calibration variable acquisition, calibration 
constant tuning, and external rapid prototyping for powertrain automotive development systems.

•

All features are independently configurable and controllable via the IEEE 1149.1 I/O port.

•

The NDI block reset is controlled with JCOMP, power-on reset, and the TAP state machine. These 
sources are independent of system reset.

31.1.3

Modes of Operation

The NDI block is in reset when the TAP controller state machine is in the TEST-LOGIC-RESET state. The 
TEST-LOGIC-RESET state is entered on the assertion of the power-on reset signal, negation of JCOMP, 
or through state machine transitions controlled by TMS. Assertion of JCOMP allows the NDI to move out 
of the reset state, and is a prerequisite to grant Nexus clients control of the TAP. Ownership of the TAP is 
achieved by loading the appropriate enable instruction for the desired Nexus client in the JTAGC controller 
(JTAGC) block when JCOMP is asserted.

Following negation of power-on reset, the NPC remains in reset until the system clock achieves lock. In 
PLL bypass mode, the NDI can transition out of the reset state immediately following negation of 
power-on reset. See 

Section 31.5, Nexus Port Controller (NPC)

, for more details.

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXR4030

Hanbay RC Series Manual preview
RC Series
Brand: Hanbay Pages: 18
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Taie FY100 Communications Manual preview
FY100
Brand: Taie Pages: 28
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Brand: Lattice Semiconductor Pages: 2
OJ Electronics EFR Series Instructions Manual preview
EFR Series
Brand: OJ Electronics Pages: 8
OJ Electronics ETO2 Manual preview
ETO2
Brand: OJ Electronics Pages: 112
OJ EFS Series Instructions Manual preview
EFS Series
Brand: OJ Pages: 17
Panosol SR658 Operation Manuals preview
SR658
Brand: Panosol Pages: 105
Pangolin FB4 Series Quick Start Manual preview
FB4 Series
Brand: Pangolin Pages: 8
J+J J4C S20 Quick Start Manual preview
J4C S20
Brand: J+J Pages: 4
Ultraflex B47 Installation Instructions Manual preview
B47
Brand: Ultraflex Pages: 7
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
Finnleo SaunaLogic SL2 Control Manual preview
SaunaLogic SL2 Control
Brand: Finnleo Pages: 14
Sparkfun Electronics Explorer Dongle Manual preview
Explorer Dongle
Brand: Sparkfun Electronics Pages: 16
Neets Control LiMa Installation Manual preview
LiMa
Brand: Neets Control Pages: 12
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Brand: AGRI TRONIX Pages: 26
TDSi DIGIgarde PLUS User Manual preview
DIGIgarde PLUS
Brand: TDSi Pages: 71
Azbil AUR455 User Manual preview
AUR455
Brand: Azbil Pages: 68

Brands by name

Popular brands

Load more brands