manualshive.com logo in svg

Freescale Semiconductor MPC5510, Reference Manual

The Freescale Semiconductor MPC5510 is a high-performance microcontroller ideal for automotive and industrial applications. For detailed specifications and instructions on how to use this product, download the free Reference Manual from 88.208.23.73:8080. This manual provides comprehensive guidance on maximizing the capabilities of the MPC5510.

Share
Download
background image

FlexRay Communication Controller (FLEXRAY)

MPC5510 Microcontroller Family Reference Manual, Rev. 1

Freescale Semiconductor

30-23

 

Preliminary

FNEAIF

Receive FIFO channel A Not Empty Interrupt Flag. This flag is set when the receive FIFO for channel A is not 
empty. If the application writes 1 to this bit, the FlexRay block updates the FIFO status, increments or wraps the 
FIFO read index in the 

Receive FIFO A Read Index Register (RFARIR)

 and clears the interrupt flag if the FIFO 

A is now empty. If the FIFO is still not empty, the FlexRay block sets this flag again. The FlexRay block generates 
the Receive FIFO A Not empty interrupt if the FNEAIE flag is asserted.
0 Receive FIFO A is empty or interrupt is disabled
1 Receive FIFO A is not empty and interrupt enabled

RBIF

Receive Message Buffer Interrupt Flag. This flag is set if for at least one of the individual receive message buffers 
(MBCCSn.MTD = 0) both the interrupt flag MBIF and the interrupt enable bit MBIE in the corresponding 

Message 

Buffer Configuration, Control, Status Registers (MBCCSRn)

 

are asserted. The application can not clear this 

RBIF flag directly. This flag is cleared by the FlexRay block when all of the interrupt flags MBIF of the individual 
receive message buffers are cleared by the application or if the application has cleared the interrupt enables bit 
MBIE. 
0 None of the individual receive message buffers has the MBIF and MBIE flag asserted.
1 At least one individual receive message buffer has the MBIF and MBIE flag asserted.

TBIF

Transmit Buffer Interrupt Flag. This flag is set if for at least one of the individual single or double transmit 
message buffers (MBCCSn.MTD = 0) both the interrupt flag MBIF and the interrupt enable bit MBIE in the 
corresponding 

Message Buffer Configuration, Control, Status Registers (MBCCSRn)

 are equal to 1. The 

application can not clear this TBIF flag directly. This flag is cleared by the FlexRay block when either all of the 
individual interrupt flags MBIF of the individual transmit message buffers are cleared by the application or the 
host has cleared the interrupt enables bit MBIE. 
0 None of the individual transmit message buffers has the MBIF and MBIE flag asserted.
1 At least one individual transmit message buffer has the MBIF and MBIE flag asserted.

MIE

Module Interrupt Enable. This flag controls if the module interrupt line is asserted when the MIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

PRIE

Protocol Interrupt Enable. This flag controls if the protocol interrupt line is asserted when the PRIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

CHIE

CHI Interrupt Enable. This flag controls if the CHI interrupt line is asserted when the CHIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

WUPIE

Wakeup Interrupt Enable. This flag controls if the wakeup interrupt line is asserted when the WUPIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

FNEBIE

Receive FIFO Channel B Not Empty Interrupt Enable. This flag controls if the receive FIFO B interrupt line is 
asserted when the FNEBIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

FNEAIE

Receive FIFO Channel A Not Empty Interrupt Enable. This flag controls if the receive FIFO A interrupt line is 
asserted when the FNEAIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

Table 30-17. GIFER Field Descriptions (Sheet 2 of 3)

Field

Description

Summary of Contents for MPC5510






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5510

Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Brand: Cansec Pages: 45
Cansec CP40 Installation Manual preview
CP40
Brand: Cansec Pages: 43
Cansec MAP2 Installation Manual preview
MAP2
Brand: Cansec Pages: 32
Hach sc200 Software Update preview
sc200
Brand: Hach Pages: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Brand: Hach Pages: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Brand: Hach Pages: 472
Hach sc1000 User Manual preview
sc1000
Brand: Hach Pages: 64
Hach SC4500 Basic User Manual preview
SC4500
Brand: Hach Pages: 210
IAI Msep First Step Manual preview
Msep
Brand: IAI Pages: 5
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Brand: NEC Pages: 30
2N 9160341 Installation Manual preview
9160341
Brand: 2N Pages: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Brand: Allen-Bradley Pages: 24
VMK VMK-I49plus Instruction Manual preview
VMK-I49plus
Brand: VMK Pages: 98
Frico IHMC6-3 Original Instructions Manual preview
IHMC6-3
Brand: Frico Pages: 8
TSM DOUBLER2 Instructions For Installing preview
DOUBLER2
Brand: TSM Pages: 2
Planar Dome Md4/PCI Installation Manual preview
Dome Md4/PCI
Brand: Planar Pages: 162
THK TJU Instruction Manual preview
TJU
Brand: THK Pages: 134
Digiplex DGP-848 Programming Manual preview
DGP-848
Brand: Digiplex Pages: 48

Brands by name

Popular brands

Load more brands