manualshive.com logo in svg

Freescale Semiconductor MPC5510, Reference Manual

The Freescale Semiconductor MPC5510 is a high-performance microcontroller ideal for automotive and industrial applications. For detailed specifications and instructions on how to use this product, download the free Reference Manual from 88.208.23.73:8080. This manual provides comprehensive guidance on maximizing the capabilities of the MPC5510.

Share
Download
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5510 Microcontroller Family Reference Manual, Rev. 1

Freescale Semiconductor

31-19

 

Preliminary

EOQFn

End-of-Queue Flag n. Indicates that an entry with an asserted EOQ bit was transferred from CFIFOn to the 
on-chip ADCs or to the external device. See 

Section 31.4.1.1, “Message Format in eQADC

,” for details about 

command message formats. When the eQADC completes the transfer of an entry with an asserted EOQ bit from 
CFIFOn, EOQFn will be set. The transfer of entries bound for the on-chip ADCs is considered completed when 
they are stored in the command buffer. If the EOQIEn bit (See 

Section 31.3.3.7, “eQADC Interrupt and eDMA 

Control Registers 0–5 (EQADC_IDCRn)

”) and EOQFn are asserted, an interrupt will be generated. Writing a 1 

clears the EOQFn bit. Writing a 0 has no effect. Refer to 

Section 31.4.3.6.2, “Command Queue Completion 

Status

,” for more information on end-of-queue flag.

0 Entry with asserted EOQ bit was not transferred from CFIFOn
1 Entry with asserted EOQ bit was transferred from CFIFOn
Note: An asserted EOQFn only implies that the eQADC has finished transferring a command with an asserted 

EOQ bit from CFIFOn. It does not imply that result data for the current command and for all previously 
transferred commands has been returned to the appropriate RFIFO.

CFUFn

CFIFO Underflow Flag n. Indicates an underflow event on CFIFOn. CFUFn is set when CFIFOn is in the 
TRIGGERED state and it becomes empty. No commands will be transferred from an underflowing CFIFO, nor 
will command transfers from lower priority CFIFOs be blocked. When CFUIEn (see Section 

Section 31.3.3.7, 

“eQADC Interrupt and eDMA Control Registers 0–5 (EQADC_IDCRn)

”) and CFUFn are both asserted, the 

eQADC generates an interrupt request.
Apart from generating an independent interrupt request for a CFIFOn underflow event, the eQADC also provides 
a combined interrupt at which the result FIFO overflow interrupt, the command FIFO underflow interrupt, and the 
command FIFO trigger overrun interrupt requests of all CFIFOs are ORed. When RFOIEn, CFUIEn, and TORIEn 
are all asserted, this combined interrupt request is asserted whenever one of the following 18 flags becomes 
asserted: RFOFn, CFUFn, and TORFn (assuming that all interrupts are enabled). See 

Section 31.4.7, “eQADC 

eDMA/Interrupt Request

,” for details. Writing a 1 clears CFUFn. Writing a 0 has no effect.

0 No CFIFO underflow event occurred
1 A CFIFO underflow event occurred

SSSn

CFIFO Single-Scan Status Bit n. When asserted, enables the detection of trigger events for CFIFOs programmed 
into single-scan level- or edge-trigger mode, and works as trigger for CFIFOs programmed into single-scan 
software-trigger mode. Refer to 

Section 31.4.3.5.2, “Single-Scan Mode

,” for further details. The SSSn bit is set 

by writing a 1 to the SSEn bit (see Section 

Section 31.3.3.6, “eQADC CFIFO Control Registers 0–5 

(EQADC_CFCRn)

”). The eQADC clears the SSSn bit when a command with an asserted EOQ bit is transferred 

from a CFIFO in single-scan mode, when a CFIFO is in single-scan level-trigger mode and its status changes 
from the TRIGGERED state due to the detection of a closed gate, or when the value of the CFIFO operation 
mode MODEn (see 

Section 31.3.3.6, “eQADC CFIFO Control Registers 0–5 (EQADC_CFCRn)

”) is changed to 

disabled. Writing to SSSn has no effect. SSSn has no effect in continuous-scan or in disabled mode.
0 CFIFO in single-scan level- or edge-trigger mode will ignore trigger events, or CFIFO in single-scan 

software-trigger mode is not triggered.

1 CFIFO in single-scan level- or edge-trigger mode will detect a trigger event, or CFIFO in single-scan 

software-trigger mode is triggered.

CFFFn

CFIFO Fill Flag n. CFFFn is set when the CFIFOn is not full. When CFFEn (see 

Section 31.3.3.7, “eQADC 

Interrupt and eDMA Control Registers 0–5 (EQADC_IDCRn)

”) and CFFFn are both asserted, an interrupt or an 

eDMA request will be generated depending on the status of the CFFSn bit. When CFFSn is negated (interrupt 
requests selected), software clears CFFFn by writing a 1 to it. Writing a 0 has no effect. When CFFSn is asserted 
(eDMA requests selected), CFFFn is automatically cleared by the eQADC when the CFIFO becomes full.
0 CFIFOn is full.
1 CFIFOn is not full.
Note: When generation of interrupt requests is selected (CFFSn=0), CFFFn must only be cleared in the ISR after 

the CFIFOn push register is accessed.

Note: CFFFn should not be cleared when CFFSn is asserted (eDMA requests selected).

bits 7–11

Reserved.

Table 31-11. EQADC_FISRn Field Descriptions (continued)

Field

Description

Summary of Contents for MPC5510






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5510

Walchem W100 Troubleshooting Manual preview
W100
Brand: Walchem Pages: 10
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
Kelly KLS4812S User Manual preview
KLS4812S
Brand: Kelly Pages: 32
Eaton Cutler-Hammer S701X25N3BP Instruction Leaflet preview
Cutler-Hammer S701X25N3BP
Brand: Eaton Pages: 4
PPI Zenex Plus User Manual preview
Zenex Plus
Brand: PPI Pages: 27
METRON FD4 Manual preview
FD4
Brand: METRON Pages: 34
Omega CN32Pt User Manual preview
CN32Pt
Brand: Omega Pages: 20
Optelec Alva BC640 User Manual preview
Alva BC640
Brand: Optelec Pages: 41
Aaeon TKS-G20-LN05 Manual preview
TKS-G20-LN05
Brand: Aaeon Pages: 54
Elan gSC2 Quick Install Manual preview
gSC2
Brand: Elan Pages: 2
Oki ML66592 User Manual preview
ML66592
Brand: Oki Pages: 466
Walchem W600 Series Instruction Manual preview
W600 Series
Brand: Walchem Pages: 88
LEGRAND 0 663 37 Quick Manual preview
0 663 37
Brand: LEGRAND Pages: 2
White Rodgers 50M58-289 Installation Instructions Manual preview
50M58-289
Brand: White Rodgers Pages: 8
Linak CB14 Product Data Sheet preview
CB14
Brand: Linak Pages: 8
DELTA DORE TYXIA 641 Installation Instructions Manual preview
TYXIA 641
Brand: DELTA DORE Pages: 80
Sundstrom SR307 User Instruction preview
SR307
Brand: Sundstrom Pages: 16
Belden Miranda NV915 Quick Start Manual preview
Miranda NV915
Brand: Belden Pages: 4

Brands by name

Popular brands

Load more brands